Correct Torque Method on Fulcrum (Rocker Arm) Bolts
#1
Correct Torque Method on Fulcrum (Rocker Arm) Bolts
Looked around on the site and found this, but it doesn't explain it very well and the Haynes manual is confusing.
https://www.ranger-forums.com/2-9l-3...m-bolts-86357/
It's supposed to be done in 2 stages, initially at 60 to 132 in-lbs and then at 18 to 26.
You start with the lifter at the lowest part of the cam.
So if one tightens the bolts to 60 to 132 in-lbs, why would you need to further go another 18 to 26.
Or does it mean to go to 18 to 26 when the valve is open ???
That doesn't make any sense though if it's already torqued to 60/132 ???
Thanks !
https://www.ranger-forums.com/2-9l-3...m-bolts-86357/
It's supposed to be done in 2 stages, initially at 60 to 132 in-lbs and then at 18 to 26.
You start with the lifter at the lowest part of the cam.
So if one tightens the bolts to 60 to 132 in-lbs, why would you need to further go another 18 to 26.
Or does it mean to go to 18 to 26 when the valve is open ???
That doesn't make any sense though if it's already torqued to 60/132 ???
Thanks !
#2
http://visualbits.net/Car%20Stuff/Fo...L%20ENGINE.pdf
Tighten it down to where it seats. Then torque it to 18
Then go to 26
To get them to seat you can turn the engine over so the cam isn't pushing on the pushrod. Hence....loosening the spring to tighten it.
I didn't, I just tightened them all down at once. Fought the spring pressure. Wasn't a big deal at all.
I essentially used the bolt to compress the spring. Then torqued it
Tighten it down to where it seats. Then torque it to 18
Then go to 26
To get them to seat you can turn the engine over so the cam isn't pushing on the pushrod. Hence....loosening the spring to tighten it.
I didn't, I just tightened them all down at once. Fought the spring pressure. Wasn't a big deal at all.
I essentially used the bolt to compress the spring. Then torqued it
#3
Thanks !
Sounds like the manual has got it backwards...
The only other engine with hydraulic lifters that I worked on was an old Chev straight six and the procedure on that was very different.
If I remember correctly, one would initially tighten the rocker arm nut with the lifters at their lower point.
You then would start the engine and allow the lifters to fill with oil (lots of clatter).
After running for a bit, one would tighten down the rocker bolt and until it was quiet and give another half turn and lock it up.
There are videos on this, but on the Vulcan engine it sounds like you simply torque down the nut and that's it _ it must have something to tighten down on to then.
I guess it had to be this way because it's pretty much impossible to adjust the rockers while the engine is running.
Sounds like the manual has got it backwards...
The only other engine with hydraulic lifters that I worked on was an old Chev straight six and the procedure on that was very different.
If I remember correctly, one would initially tighten the rocker arm nut with the lifters at their lower point.
You then would start the engine and allow the lifters to fill with oil (lots of clatter).
After running for a bit, one would tighten down the rocker bolt and until it was quiet and give another half turn and lock it up.
There are videos on this, but on the Vulcan engine it sounds like you simply torque down the nut and that's it _ it must have something to tighten down on to then.
I guess it had to be this way because it's pretty much impossible to adjust the rockers while the engine is running.
#4
#5
This procedure had to be done on the old Mazda B2200's because it would take a week for the thing to quiet down.
The lifters on the old B2200's were very problematic though.
Thread
Thread Starter
Forum
Replies
Last Post
mlw20lu
8-Cylinder Tech
7
01-16-2012 01:22 PM
dave01978
Auto Detailing 101
0
12-02-2004 01:59 AM