4wd Uprights vs 2wd Edge uprights
#1
4wd Uprights vs 2wd Edge uprights
Hey guys, I am replacing all my front ball joints, bushings, and tie rod ends next week. I cross checked all the part numbers I ordered and they match that of 4wd rangers and explorers.
So I was thinking I could stop by the junkyard and pick up some 4wd uprights and maybe the brakes, I need to look into that, and put those in just in case I decide to add 4wd later on.
I am basically wondering if there would be any problem running 4wd uprights without having the axle shafts going to them? Also since mist of you have more experience on rangers than me, if anyone has any input on this? Thanks!
David
So I was thinking I could stop by the junkyard and pick up some 4wd uprights and maybe the brakes, I need to look into that, and put those in just in case I decide to add 4wd later on.
I am basically wondering if there would be any problem running 4wd uprights without having the axle shafts going to them? Also since mist of you have more experience on rangers than me, if anyone has any input on this? Thanks!
David
#2
#4
Yes spindles, that is the word I was trying to think of. Are you talking about this thread?
https://www.ranger-forums.com/showthread.php?t=130310
It seems from that that the 2wd edge and 4wd have the same control arms, therefore the spindles should be interchangeable?
https://www.ranger-forums.com/showthread.php?t=130310
It seems from that that the 2wd edge and 4wd have the same control arms, therefore the spindles should be interchangeable?
#5
The dimensions are slightly off between the two. I remember an ex member here went by the username "D" tried to use the 4x2 UCAs on his edge and it wouldn't work. He ended up custom fabbing his own.
Good point on the brakes, i will look into what I need thanks.
#9
#12
#13
Did you pay attention to what this post is about, clearly I know they are different that is why I said I would go pull them off of a 4wd. I referred to them as uprights and not spindles or knuckles, he put knuckle in bold probably because he is suggesting that spindle and upright are incorrect words and that knuckle is the correct term. If you are going to try to be condescending you should read the whole post first.
#14
#16
SPINDLE:
KNUCKLE:
However, since you'd have to pull it all apart to put the drivetrain parts in anyway, what are you gaining by swapping them now?
And LOL Dave, gotta relax a bit.
#17
For the record, there is actually a difference between spindle and knuckle:
SPINDLE:
KNUCKLE:
They will not get ruined. I'm not sure where this idea comes from, but I've seen many vehicles run like this. Just take the end of a cv shaft, clean it up, and slide it into the spindle. This just gives the center of the bearing more support against losing shape.
However, since you'd have to pull it all apart to put the drivetrain parts in anyway, what are you gaining by swapping them now?
And LOL Dave, gotta relax a bit.
SPINDLE:
KNUCKLE:
They will not get ruined. I'm not sure where this idea comes from, but I've seen many vehicles run like this. Just take the end of a cv shaft, clean it up, and slide it into the spindle. This just gives the center of the bearing more support against losing shape.
However, since you'd have to pull it all apart to put the drivetrain parts in anyway, what are you gaining by swapping them now?
And LOL Dave, gotta relax a bit.
#18
Originally Posted by 04RangerDave
my next response was go get the parts and see what happens when you do it your way. But then you spoke up
Originally Posted by ME00Stepside
They will not get ruined. I'm not sure where this idea comes from, but I've seen many vehicles run like this. Just take the end of a cv shaft, clean it up, and slide it into the spindle. This just gives the center of the bearing more support against losing shape.
However, since you'd have to pull it all apart to put the drivetrain parts in anyway, what are you gaining by swapping them now?
However, since you'd have to pull it all apart to put the drivetrain parts in anyway, what are you gaining by swapping them now?
Said they would get ruined, and I guess the deformation is what he was talking about. I haven't actually gotten under the truck to look into the 4wd swap yet, I will add all of the front drive components if I have the mounts there, but in the one post I saw the guy had to weld his own mount in, and I do not have access to a welder right now. Plus I was thinking that if I did this part now I could get it aligned and then when I add the rest in it won't have to get realigned.
thanks for the reply and the vocabulary lesson, good to know
#19
The 4wd wheel bearings have a giant hole in the center where the cv axle rides.
1 debris will enter the hole kill the bearing
2 the wheel bearing is supported by cv
You should avoid the explorer front axles with the passenger side axle tube disconnect. If you want a live axle truck get wheel bearings and cv shafts for 95+01 explorers or 01+ rangers. If you want manual hubs get wheel bearings for 98-00 along with the cv's.
Didn't mean to create an uprising over bolding one word. So lets clarify, the knuckle is what bolt to the suspension on most 4wd trucks. Spindles are where the wheel bearing usally rides. The 4wd ranger has a knuckles and unit bearing so it has no spindle per say, but the 2wd ranger has both and commonly referred to as just a spindle. As I believe they are one piece.
Lets use the D44 for an example.
Spindle
Knuckle
As you can see the ranger doesn't really fit the spindle category in 4wd trim. Just trying to show the difference not tweak peeps.
1 debris will enter the hole kill the bearing
2 the wheel bearing is supported by cv
You should avoid the explorer front axles with the passenger side axle tube disconnect. If you want a live axle truck get wheel bearings and cv shafts for 95+01 explorers or 01+ rangers. If you want manual hubs get wheel bearings for 98-00 along with the cv's.
Didn't mean to create an uprising over bolding one word. So lets clarify, the knuckle is what bolt to the suspension on most 4wd trucks. Spindles are where the wheel bearing usally rides. The 4wd ranger has a knuckles and unit bearing so it has no spindle per say, but the 2wd ranger has both and commonly referred to as just a spindle. As I believe they are one piece.
Lets use the D44 for an example.
Spindle
Knuckle
As you can see the ranger doesn't really fit the spindle category in 4wd trim. Just trying to show the difference not tweak peeps.
Thread
Thread Starter
Forum
Replies
Last Post
bleech1
General Technical & Electrical
11
11-14-2019 09:38 AM
wvcat
General Technical & Electrical
0
05-04-2009 07:07 AM