Blower motor - Ranger-Forums - The Ultimate Ford Ranger Resource


General Ford Ranger Discussion General discussion of the Ford Ranger that does not fit in any other sub-forum.

Reply
 
LinkBack Thread Tools Search this Thread
  #1  
Old 04-10-2009
Yellow_edge_4x4's Avatar
Member
Thread Starter
 
Join Date: Oct 2008
Location: Bryan, OH
Posts: 723
Blower motor

Ok I think my blower motor is going out. When I have the heat to full it dosent blow out that hard. It dose get warm but wont blow it out. Where is the blower motor located at and how hard is to to change it youself? Would it be cheaper to get one from a junk yard or just get a new one?
Reply With Quote
  #2  
Old 04-10-2009
Level III Supporter
iTrader: (2)
 
Join Date: Jun 2004
Location: usa
Posts: 24,936
does it stay like the same speed at any spot? might be the resistor known to rust out and go bad
Reply With Quote
  #3  
Old 04-10-2009
Yellow_edge_4x4's Avatar
Member
Thread Starter
 
Join Date: Oct 2008
Location: Bryan, OH
Posts: 723
yes. Lowest setting and highest setting seem to be the same. Where is the resistor loacated at??
Reply With Quote
  #4  
Old 04-11-2009
bjohnson238's Avatar
Member
 
Join Date: Nov 2008
Location: Muncie, IN
Posts: 732
It is at the right rear of the engine compartment near the blower motor.
Reply With Quote
  #5  
Old 04-11-2009
Member
 
Join Date: Mar 2007
Location: Brooklyn NY and Deposit NY
Posts: 243
its the resistor you need a good quarter inch drive socket set with extensions and a swivel to get it out there s a plug with like six wires to it and thats it
Reply With Quote
  #6  
Old 04-11-2009
Level III Supporter
iTrader: (2)
 
Join Date: Jun 2004
Location: usa
Posts: 24,936
ya they sell the resistor and new resistor plug you cut the wires and connect the new one's they get all corroded
Reply With Quote
  #7  
Old 04-12-2009
Yellow_edge_4x4's Avatar
Member
Thread Starter
 
Join Date: Oct 2008
Location: Bryan, OH
Posts: 723
Ok I pulled the resistor today, the springs look fine not rusted or anything. The conections were rusty so I tryed to sand the rust off just to see if it would work and it didnt. Now it wont blow at all.
Reply With Quote
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Blower motor resistor issues Savaking72 General Ford Ranger Discussion 6 12-23-2011 08:40 PM
10 amp fuse for blower motor relay blowing barebull98 General Technical & Electrical 21 12-24-2010 03:04 PM
Heater, A/C Blower Motor Resister Pack Scrambler82 General Technical & Electrical 4 01-09-2010 06:45 AM
blower motor wont turn on bman 2.3L & 2.5L I4 Tech 5 12-09-2009 10:22 AM
Blower motor new, but next to no air flow devildog271203 General Technical & Electrical 8 10-27-2007 07:10 AM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -6. The time now is 04:43 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.