General Ford Ranger Discussion General discussion of the Ford Ranger that does not fit in any other sub-forum.

New, Need Help..

Old Apr 21, 2007
  #1  
LiftedRanger226's Avatar
Thread Starter
|
Member
Joined: Apr 2007
Posts: 7
Likes: 0
From: Everett, PA
New, Need Help..

Ok so I just got a 1988 Ranger with a 2.3L 4cyl. with 117,000 miles on it. It has a 9 inch lift and 31" tires. This thing SUCKS for power. I can hold it to the floor in 1st and pop the clutch and it all but stalls...sometimes it does. My buddy has a 3.8 from an older Mercury Capri, and I was wondering if I could put it in my truck. Would it bolt up to the stock 4cyl. 5 speed tranny? Because he doesnt have the tranny...so would my tranny with this 3.8 work? Also will I need to get the computer from the 3.8 too? I need help bad. Thanks alot guys!
 
Reply
Old Apr 21, 2007
  #2  
Redneckstone's Avatar
Level III Supporter
iTrader: (2)
Joined: Jun 2004
Posts: 24,936
Likes: 11
From: usa
highly doupt it... have you regeared the truck? might want to look into like 4.56 easy...
 
Reply
Old Apr 21, 2007
  #3  
Hanzo Steel's Avatar
Member
Joined: Dec 2006
Posts: 593
Likes: 0
From: Aurora, Co/SFV, Ca.
Heres some things to look forward to?

http://www.therangerstation.com/tech...onversion.html
 
Reply
Old Apr 21, 2007
  #4  
Needforspeed3685's Avatar
Joined: Aug 2005
Posts: 1,836
Likes: 11
From: Lowell, AR
I have a 4.10 geared rear axle and diff assembly, if you want it!
 
Reply
Old Apr 21, 2007
  #5  
94greenmachine's Avatar
Joined: Aug 2006
Posts: 554
Likes: 1
From: Virginia Beach, VA
Originally Posted by Needforspeed3685
I have a 4.10 geared rear axle and diff assembly, if you want it!
LSD??????
 
Reply
Old Apr 21, 2007
  #6  
phat_95_ranger_xlt's Avatar
Joined: Mar 2007
Posts: 126
Likes: 0
From: mexia texas
Originally Posted by Needforspeed3685
I have a 4.10 geared rear axle and diff assembly, if you want it!
how much?
 
Reply
Old Apr 21, 2007
  #7  
94greenmachine's Avatar
Joined: Aug 2006
Posts: 554
Likes: 1
From: Virginia Beach, VA
If it has LSD, I will take it for 450!
 
Reply
Old Apr 21, 2007
  #8  
Needforspeed3685's Avatar
Joined: Aug 2005
Posts: 1,836
Likes: 11
From: Lowell, AR
Sorry dudes...it's a 7.5 OPEN diff...
 
Reply
Old Apr 21, 2007
  #9  
Machine090767's Avatar
RF Veteran
Joined: May 2006
Posts: 6,410
Likes: 0
From: Minnesota
not to be a jerk, but i laugh at people (not at you, ray, you bought the truck like this) when they say they have a 2.3, 2.8, or a 2.9 with a lift and mudders and have stock gearing. now, this may seem harsh, but why don't more people upgrade the gearing first, then do the lift and tires?
 
Reply
Old Apr 21, 2007
  #10  
got-dirty's Avatar
Member
Joined: May 2005
Posts: 3,829
Likes: 0
From: Sliding in the skreets
the install side of the mod. not many people know how to do them, so a DIY easy way out is not usually an option. and most people dont think they need gears until they feel the loss in the performance in their vehicle.
 
Reply
Old Apr 22, 2007
  #11  
LiftedRanger226's Avatar
Thread Starter
|
Member
Joined: Apr 2007
Posts: 7
Likes: 0
From: Everett, PA
ok well i put my 17 inch wheels from my mustang on it, lmfao its so funny looking...so i have enough power now, but its overheating. Yesterday when it overheated I checked the oil and it was down a good bit so i added a quart...let it run a while and the oil light came on again. Checked it and it was fine...so wtf? And the overheating thing I have no clue why its doing that.. it builds up pressure because it will spray when you undo the pressure cap while its running and its circulating but it wont stop overheating. it doesnt do it at idle only when you run it. HELPP!!!!
 

Last edited by LiftedRanger226; Apr 22, 2007 at 12:28 PM.
Reply
Old Apr 22, 2007
  #12  
Hanzo Steel's Avatar
Member
Joined: Dec 2006
Posts: 593
Likes: 0
From: Aurora, Co/SFV, Ca.
You didn't check the oil till now?
 
Reply
Old Apr 22, 2007
  #13  
LiftedRanger226's Avatar
Thread Starter
|
Member
Joined: Apr 2007
Posts: 7
Likes: 0
From: Everett, PA
i just got it yesterday
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
2007BlackFX4
Suspension Tech
3
Jun 3, 2010 07:36 PM
DeMar17
Audio & Video Tech
8
Jun 10, 2009 06:45 AM
01edgeMan
Audio & Video Tech
6
Jan 11, 2009 06:28 PM


Thread Tools
Search this Thread

All times are GMT -6. The time now is 12:58 PM.