to those of you with a body lift and a manual transmission......
#27
Originally Posted by RazorsEDGE
That will be another one of those elusive parts. I turned to my dealer about the part, but they insisted that it never existed and that the only RCM cover was the twin cup holder console. I PM'd Bob about the part for help locating it and he gave his to me. I'd probably still be looking for some of the LVL II parts iif it wasn't for him.
Originally Posted by DangaRanger99
iMaurice you could do a hurst with Wayne's shifter lifter
#29
#30
I pulled the cover today and got the part # from the underside of it, there were three of them stamped on it. I looked on www.fastpartsnetwork.com and the #'s netted no results, but maybe you would have better luck asking a dealer to look it up.
part number:
3L54-13130B24-AAW
2L54-13130B24-AAW
2L54-13130B24-ABW
part number:
3L54-13130B24-AAW
2L54-13130B24-AAW
2L54-13130B24-ABW
#32
Originally Posted by RazorsEDGE
I pulled the cover today and got the part # from the underside of it, there were three of them stamped on it. I looked on www.fastpartsnetwork.com and the #'s netted no results, but maybe you would have better luck asking a dealer to look it up.
part number:
3L54-13130B24-AAW
2L54-13130B24-AAW
2L54-13130B24-ABW
part number:
3L54-13130B24-AAW
2L54-13130B24-AAW
2L54-13130B24-ABW
I can't locate those on http://www.trademotion.com/partlocat...?siteid=213787 either...
I do have an 02 and 03 VIN so I could just call the dealership and see if they could help.
#34
Originally Posted by lifted97ranger
Chris can you get the part number for the shifter surrond? you have the Level II shifter without the manual t-case don't ya?
I'll try to get photos tomorrow after work and go from there?
anyone have a good source for aftermarket carpet? Ford wants $350 for 02 or 03 ebony carpet. The hole cut in my carpet for my shifter is just barely too large and I'm trying to keep an OEM look. If I could pay off this blasted CC of mine I'd just put the carpet on it.
EDIT: You know, the old style of twin shifter console and boots wouldn't look too bad either. It would hold me over until I could get the right carpet too.
Last edited by Lefty04LevelII; 12-05-2007 at 09:30 PM.
#36
Originally Posted by Lefty04LevelII
Yes, I have the double cup holder console (is that what you're talking about) and my factory LII shifter. Or are you talking about the floor plate?
I'll try to get photos tomorrow after work and go from there?
anyone have a good source for aftermarket carpet? Ford wants $350 for 02 or 03 ebony carpet. The hole cut in my carpet for my shifter is just barely too large and I'm trying to keep an OEM look. If I could pay off this blasted CC of mine I'd just put the carpet on it.
EDIT: You know, the old style of twin shifter console and boots wouldn't look too bad either. It would hold me over until I could get the right carpet too.
I'll try to get photos tomorrow after work and go from there?
anyone have a good source for aftermarket carpet? Ford wants $350 for 02 or 03 ebony carpet. The hole cut in my carpet for my shifter is just barely too large and I'm trying to keep an OEM look. If I could pay off this blasted CC of mine I'd just put the carpet on it.
EDIT: You know, the old style of twin shifter console and boots wouldn't look too bad either. It would hold me over until I could get the right carpet too.
Summit has new carpet kits for $124
Thread
Thread Starter
Forum
Replies
Last Post
Dynasty
General Ford Ranger Discussion
19
11-04-2022 11:53 AM
04blackedge
OLD - Interior, Exterior, Electrical, & Misc.
1
05-07-2009 04:43 PM
rngprerunner
General Ford Ranger Discussion
6
01-04-2008 12:07 PM
Mike9825
General Ford Ranger Discussion
4
07-21-2006 02:16 PM