General Technical & Electrical General technical and electrical discussion for the Ford Ranger that does not fit in any other sub-forum.

1990 ranger starting problem

Old Nov 26, 2010
  #1  
Benjamix's Avatar
Thread Starter
|
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: Farmington, MN
1990 ranger starting problem

I need help with my truck, it wont start or even turn over.

About a mounth ago I had to jump it to get it to start, that same day it over heated and wont start since.

I've replaced the battery, both positive cables, negative cable, Solenoid

When I put the battery in all the lights where bright inside, then when I went to start it the solind made a tick sound and the lights turned off. when I dicontect the cables and try agian it does the same thing.

Does anyone know what this problem could be.

Thanks - Benjamix
 
Reply
Old Nov 26, 2010
  #2  
87xlt's Avatar
Member
Joined: Jun 2008
Posts: 876
Likes: 3
From: In my truck!
Sounds like a bad starter? Have you tried to turn the engine over by hand?
 
Reply
Old Nov 26, 2010
  #3  
Benjamix's Avatar
Thread Starter
|
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: Farmington, MN
the starter is fine. the motor will turn over by hand
 
Reply
Old Nov 26, 2010
  #4  
green95fordranger's Avatar
Joined: Mar 2010
Posts: 14
Likes: 0
From: fenton,michigan
the part with the lights going out after the solenoid clicks confuses me. but if the starter wont physically turn to start the engine, that sounds like a bad ground through the starter. to fix that you would need to remove the starter and break down the 3 sections of it and sand each end and replace.
 
Reply
Old Nov 27, 2010
  #5  
Benjamix's Avatar
Thread Starter
|
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: Farmington, MN
I pulled out the alternator and it tested bad, I think thats what fried my battery.

Thanks for the help!
 
Reply
Old Nov 27, 2010
  #6  
87xlt's Avatar
Member
Joined: Jun 2008
Posts: 876
Likes: 3
From: In my truck!
Did the truck start?
 
Reply
Old Nov 27, 2010
  #7  
green95fordranger's Avatar
Joined: Mar 2010
Posts: 14
Likes: 0
From: fenton,michigan
dont pay for a used or new starter... clean it, its free and it worked twice for me. not to mention how easy it is!
 
Reply
Old Nov 27, 2010
  #8  
87xlt's Avatar
Member
Joined: Jun 2008
Posts: 876
Likes: 3
From: In my truck!
Same here man! The hardest part is holding the brushes in while putting the starter back together.
 
Reply
Old Nov 28, 2010
  #9  
Benjamix's Avatar
Thread Starter
|
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: Farmington, MN
not yet. I have to get the part monday
 
Reply
Old Nov 28, 2010
  #10  
Benjamix's Avatar
Thread Starter
|
Member
Joined: Nov 2010
Posts: 5
Likes: 0
From: Farmington, MN
I just repalced the starter not too long ago, so I'm pretty sure thats not the prob. I'll have to try cleaning on sometime.

Thanks
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
doug Rooney
Drivetrain Tech
0
Dec 2, 2013 02:57 AM
smokindmax
SOHC - 2.3L & 2.5L Lima Engines
5
Sep 1, 2009 10:33 AM
scoutsize
SOHC - 2.3L & 2.5L Lima Engines
7
Jul 5, 2009 01:28 PM
jdckpdl
Drivetrain Tech
0
Jun 12, 2009 09:49 AM
TheBigFUGR
General Technical & Electrical
1
Dec 6, 2007 06:20 PM


Thread Tools
Search this Thread

All times are GMT -6. The time now is 05:49 PM.