Trying to ACTIVATE my seat belt warning
#1
Trying to ACTIVATE my seat belt warning
Yes, some of you are going to be puzzled as to why I want to do this, but I'm trying to ACTIVATE my seat belt warning cluster light/buzzer.
I've tried this proceedure:
Before following the procedure, ensure that the following conditions are met:
*The parking brake is set
*The gearshift is in Park (auto trans) or neutral (manual trans)
*The ignition switch is in the OFF position
*All vehicle doors are closed
*The driver's safety belt is unbuckled
*The parklamps/headlamps are in the OFF position
Activation/Deactivation procedure:
1. Turn the ignition switch to RUN (or ON) position. (Don't start the engine)
2. Wait until the safety belt warning light turns off. (Approx. 1-2 minutes)
*Steps 3-5 must be completed within 60 seconds or the procedure will have to be repeated.
3. Buckle then unbuckle the safety belt 3 times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation.
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
5. Buckle then unbuckle the safety belt 3 times, ending with belt unbuckled.
*After step 5 the safety belt warning light will be turned on for 3 seconds.
6. Within 7 seconds of safety belt warning light turning off, buckle then unbuckle the belt.
*This will disable Beltminder if it is currently enabled, or enable it if it's currently disabled.
7. Confirmation of disabling Beltminder is provided by the safety belt warning light flashing 4 times per second for 3 seconds.
8. Confirmation of enabling BeltMinder is provided by:
*The safety belt warning light flashing 4 times per second for 3 seconds.
*Followed by 3 seconds with the safety belt warning light off.
*Once again, the safety belt warning light will flash 4 times per second for 3 seconds.
9. After receiving confirmation, the deactivation/activation procedure is complete.
Step 2 above is where I have a problem; since it appears that a previous owner has DISABLED the seat belt reminding system, I never see the saftey belt warning light on when the key is turned to "on"., so how can I wait for it to turn off??? I've tried waiting two minutes anyhow, then going on with the procedure, but it does not activate after step 8.
Has anyone else ever re-activated their seat belt warning after disabling it? How do you get past step 2 if you have?
I've tried this proceedure:
Before following the procedure, ensure that the following conditions are met:
*The parking brake is set
*The gearshift is in Park (auto trans) or neutral (manual trans)
*The ignition switch is in the OFF position
*All vehicle doors are closed
*The driver's safety belt is unbuckled
*The parklamps/headlamps are in the OFF position
Activation/Deactivation procedure:
1. Turn the ignition switch to RUN (or ON) position. (Don't start the engine)
2. Wait until the safety belt warning light turns off. (Approx. 1-2 minutes)
*Steps 3-5 must be completed within 60 seconds or the procedure will have to be repeated.
3. Buckle then unbuckle the safety belt 3 times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation.
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
5. Buckle then unbuckle the safety belt 3 times, ending with belt unbuckled.
*After step 5 the safety belt warning light will be turned on for 3 seconds.
6. Within 7 seconds of safety belt warning light turning off, buckle then unbuckle the belt.
*This will disable Beltminder if it is currently enabled, or enable it if it's currently disabled.
7. Confirmation of disabling Beltminder is provided by the safety belt warning light flashing 4 times per second for 3 seconds.
8. Confirmation of enabling BeltMinder is provided by:
*The safety belt warning light flashing 4 times per second for 3 seconds.
*Followed by 3 seconds with the safety belt warning light off.
*Once again, the safety belt warning light will flash 4 times per second for 3 seconds.
9. After receiving confirmation, the deactivation/activation procedure is complete.
Step 2 above is where I have a problem; since it appears that a previous owner has DISABLED the seat belt reminding system, I never see the saftey belt warning light on when the key is turned to "on"., so how can I wait for it to turn off??? I've tried waiting two minutes anyhow, then going on with the procedure, but it does not activate after step 8.
Has anyone else ever re-activated their seat belt warning after disabling it? How do you get past step 2 if you have?
#2
RF Veteran
iTrader: (1)
Hopefully previous owner did see this video:
The light not coming on is troublesome since that is not disabled by any Ford user procedures, just the chime.
Could be someone has pulled the bulb, or check connectors under drivers seat.
Does the SRS(airbag) light come on and go off like it should when key is turned on?
The light not coming on is troublesome since that is not disabled by any Ford user procedures, just the chime.
Could be someone has pulled the bulb, or check connectors under drivers seat.
Does the SRS(airbag) light come on and go off like it should when key is turned on?
Last edited by RonD; 12-17-2014 at 10:54 AM.
#3
Yep, the airbag comes on with the key (had to relace that tiny bulb on the 'enable/disable' key control module in the lower central dash, as it burned out one day and gave me the typical code for that. Pretty darn sure the bulb is good for the seat belt too, as when I had the cluster out to replace some cluster lights, I checked them all with a ohm meter for continuity. Even though it never lights though....
The plug under the seat is intact and connected too, as I had the seats removed a few weeks ago to use a good carpet cleaner (steam cleam) to get the years of "funk" smell out.
I thought the buzzer/chime was in the GEM module for our 2000 Rangers? The cluster in this video is not like mine at all. My cluster still has the anti-slosh module in the corner, which this cluster does not have (in the video).
The plug under the seat is intact and connected too, as I had the seats removed a few weeks ago to use a good carpet cleaner (steam cleam) to get the years of "funk" smell out.
I thought the buzzer/chime was in the GEM module for our 2000 Rangers? The cluster in this video is not like mine at all. My cluster still has the anti-slosh module in the corner, which this cluster does not have (in the video).
Last edited by bucko; 12-17-2014 at 02:10 PM.
#4
The plug under the seat is intact and connected too, as I had the seats removed a few weeks ago to use a good carpet cleaner (steam cleam) to get the years of "funk" smell out.
I thought the buzzer/chime was in the GEM module for our 2000 Rangers? The cluster in this video is not like mine at all. My cluster still has the anti-slosh module in the corner, which this cluster does not have (in the video).
I thought the buzzer/chime was in the GEM module for our 2000 Rangers? The cluster in this video is not like mine at all. My cluster still has the anti-slosh module in the corner, which this cluster does not have (in the video).
You can try grounding the brown/lt blue wire under the drivers seat with the key in the run position to see if the light/chime will come on.
#5
Thread
Thread Starter
Forum
Replies
Last Post
kalifornia
General Technical & Electrical
4
04-16-2013 09:49 AM
vagrants
General Technical & Electrical
0
04-26-2011 11:07 AM
gvranger
Wheels & Tires Semi-Tech
18
08-12-2005 08:09 PM
MyYellowRanger
Interior Semi-Tech
11
06-15-2004 01:51 PM