For Sale: Hurst shifter (CO)
#1
Hurst shifter (CO)
Was installed in my 04 for about a month, before removing due to leaking issues. I have been really busy with work and getting ready for college next year and just haven't had much time to address the problem. I could also use the money for college.
I am asking $170, I bought it for $220 on summit. I can meet up to 20 miles from Colorado Springs. I am also willing to ship as long as a means of payment is discussed.
The boot has already been cut, to fit beneath cup holders. Attached picture shows everything that will be sold.
I am asking $170, I bought it for $220 on summit. I can meet up to 20 miles from Colorado Springs. I am also willing to ship as long as a means of payment is discussed.
The boot has already been cut, to fit beneath cup holders. Attached picture shows everything that will be sold.
Last edited by EStrauch12; 03-04-2012 at 08:05 AM.
#3
Was installed in my 04 for about a month, before removing due to leaking issues. I have been really busy with work and getting ready for college next year and just haven't had much time to address the problem. I could also use the money for college.
I am asking $170, I bought it for $220 on summit. I can meet up to 20 miles from Colorado Springs. I am also willing to ship as long as a means of payment is discussed.
The boot has already been cut, to fit beneath cup holders. Attached picture shows everything that will be sold.
I am asking $170, I bought it for $220 on summit. I can meet up to 20 miles from Colorado Springs. I am also willing to ship as long as a means of payment is discussed.
The boot has already been cut, to fit beneath cup holders. Attached picture shows everything that will be sold.
#4
I have a really big favor to ask if you would not mind? I have a complete shifter EXCEPT for the mounting plate that bolts to the transmission. It is in the center of your photo. I would like to make one, but up till now I have been unable to get the proper dimensions. If it is not to much trouble could you measure your plate for me. I have uploaded a photo to show what dimensions I need. Thank you VERY MUCH!
#6
I have the exact same problem, got the shifter without a mounting plate and Hurst will not sell just the plate. I wish you was closer I would let you use my digital calliper. Hope to get some measurements and get a shop to mill it out for me out of 6061 Aluminum.
#7
Hurst Mounting Plate DImensions:
TOP VIEW
A: 7.5 cm 3 in
B: 3.5 cm 1 3/8 in
BOTTOM VIEW
B 3.5 cm 1 3/8 in (same measurement as top view B)
C 4 cm 1 9/16 in
SIDE VIEW
D .6 cm 1/4 in
E 1 cm 3/8 in
I took these measurements as precisely as possible with out the use of a digital caliper. Let me know if you have any further questions. Good luck!
TOP VIEW
A: 7.5 cm 3 in
B: 3.5 cm 1 3/8 in
BOTTOM VIEW
B 3.5 cm 1 3/8 in (same measurement as top view B)
C 4 cm 1 9/16 in
SIDE VIEW
D .6 cm 1/4 in
E 1 cm 3/8 in
I took these measurements as precisely as possible with out the use of a digital caliper. Let me know if you have any further questions. Good luck!
#8
Hurst Mounting Plate DImensions:
TOP VIEW
A: 7.5 cm 3 in
B: 3.5 cm 1 3/8 in
BOTTOM VIEW
B 3.5 cm 1 3/8 in (same measurement as top view B)
C 4 cm 1 9/16 in
SIDE VIEW
D .6 cm 1/4 in
E 1 cm 3/8 in
I took these measurements as precisely as possible with out the use of a digital caliper. Let me know if you have any further questions. Good luck!
TOP VIEW
A: 7.5 cm 3 in
B: 3.5 cm 1 3/8 in
BOTTOM VIEW
B 3.5 cm 1 3/8 in (same measurement as top view B)
C 4 cm 1 9/16 in
SIDE VIEW
D .6 cm 1/4 in
E 1 cm 3/8 in
I took these measurements as precisely as possible with out the use of a digital caliper. Let me know if you have any further questions. Good luck!
Did you sell your shifter yet? You shouldn't have any problem selling it.
They are quite popular.
Thread
Thread Starter
Forum
Replies
Last Post