Drivetrain Tech General discussion of drivetrain for the Ford Ranger.

regear ratio questions

Thread Tools
 
Search this Thread
 
  #1  
Old 03-31-2010
silverfox's Avatar
Member
Thread Starter
Join Date: Jul 2008
Location: Taft, Ca
Posts: 1,040
Likes: 0
Received 1 Like on 1 Post
regear ratio questions

im looking at regearing my stock gearing is 4.10's the power loss with the 31's hasnt been to bad but any power loss with a 4 banger is to much using the online guides i figure 4.56 should put me back to stock but im thinking about over gearing it a bit to say 4.88's will this harm anything other than mpg's i know my rpms will be a little higher at highway speeds ill also be getting a tuner and i see there are different kinds of install kits what kind would i need full or minor

this is a few month down the road just getting ready to start saving up for everything
 
  #2  
Old 03-31-2010
silverfox's Avatar
Member
Thread Starter
Join Date: Jul 2008
Location: Taft, Ca
Posts: 1,040
Likes: 0
Received 1 Like on 1 Post
bump
 
  #3  
Old 04-07-2010
donnytrash's Avatar
Member
Join Date: Mar 2010
Location: laguna niguel
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
456 is for 33s I've seen people do a 488 with 33s aswell but that will be reving a lot higher. I have a 410 with 31s and the 2.3L and its pretty gutless . I'm going to swap up to the 4.56 and see how it is and then get bigger tires eather 33 or 32s
 
  #4  
Old 04-07-2010
timpat92855's Avatar
Member
iTrader: (1)
Join Date: Nov 2006
Location: Lousiville, MS
Posts: 1,067
Likes: 0
Received 2 Likes on 2 Posts
The autotrans kills your power with bigger tires. I would go 4.56. the 2.3 dura really likes rpm and it would probably do ok with up to a 33in tire.

What size rear end do you have? 7.5 or 8.8
 
  #5  
Old 04-07-2010
silverfox's Avatar
Member
Thread Starter
Join Date: Jul 2008
Location: Taft, Ca
Posts: 1,040
Likes: 0
Received 1 Like on 1 Post
mines a 7.5
 
  #6  
Old 04-07-2010
silverfox's Avatar
Member
Thread Starter
Join Date: Jul 2008
Location: Taft, Ca
Posts: 1,040
Likes: 0
Received 1 Like on 1 Post
ok ima do some math
225-70r15=27.4(stock size)
numbers off of 4.10 gear ratio
27 inch tire=3325rpms
28 inch tire=3206rpms
3325-3206=119 divided by 10=11.9x4=47.6 round up to 48
3325+48=3373

4.10 gear ratio
3373=27.4 inch tire (stock rpms)
2896=31 tire

4.56 gear ratio
3213 rpms on 31's

4.88 gear ratio
3428 rpms on 31's

so should i loose 160 rpms with the 4.56 or should i gain 55 rpms with the 4.88 (as compared to stock)?

numbers based off of this chart and my math i understand 4.11 is not the same as 4.10 but its all i could find
http://www.4wheelonline.com/images/gear-chart.gif
 

Last edited by silverfox; 04-07-2010 at 10:38 AM.
  #7  
Old 04-07-2010
silverfox's Avatar
Member
Thread Starter
Join Date: Jul 2008
Location: Taft, Ca
Posts: 1,040
Likes: 0
Received 1 Like on 1 Post
i may add my next set of tires will be 32's
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
DaneTrain
Drivetrain Tech
28
09-26-2006 04:38 PM
dodge_cowboy
Drivetrain Tech
17
08-04-2006 11:17 PM
RicksTJR
Drivetrain Tech
41
06-05-2006 01:56 AM
jimmclrk1
Drivetrain Tech
14
11-03-2005 07:44 PM
mcerwing
Drivetrain Tech
4
08-28-2005 08:57 PM



Quick Reply: regear ratio questions



All times are GMT -6. The time now is 06:07 PM.