5.0L plans
#252
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
Finally an update. Got the block surface finally prepped for install off the heads. still need to chase the threads, havent worked on the rear end tho im really wanting to but as always ballistic is slow on shipping so my stuff wont even be here for another week and i need to find a welder to use in the mean time ugh. thats about it.. Im reallyhoping to get everything i need and crack down and finish this thing here in the next month or two max. I just want to cross all my T's and dot my I's, i cant afford any hiccups during install lol
#253
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
#257
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
#259
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
#260
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
#261
#263
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
#265
If you run a mega shifter you will run into problems with the shifter lever that goes into the tranny, because it still has to operate the TRS. B&M does not make (to my knowledge) a shift lever that will still operate the TRS. But i do belive that art carr make the correct shift lever. I rigged my shift lever up to make it work its not pretty but it works.
#266
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
well i dont like riggin stuff up unless i have to. Im sure it works perfect for you but, with all the work involved id rather just get one i know will work with no modding lol. However it would look kickass. i would actually move it up and put it towards the front where the stock manual shifter is =)
#268
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
Ordered Diff cover today.. Cheap Summit chrome. Idc im gonna spray it with Metalcast. I cant jusitfy droppin 100 on a HD one when i dont wheel.
i know this is small. but any suggestions on which spark plug i should run?
Idiot me orderd all the wrong junk from ballistic so im sending that back today.
next week im relly goign to concentrate on finishing the other head. and get it ready to install. I still neet to shim the springs and lap the valves, clean the surface and repaint.
Next weekend going to JY for Radiator, Auto Column, oil lines, and motor mounts. I have found ones on ebay but I need the Block Plates too! sucks. Gotta wait a little bit for the rear brakes and ECM tune.. Need to get some money set aside first.. Then im done!! Sorta
Tre, any word on shipping that pedal assembly?
i know this is small. but any suggestions on which spark plug i should run?
Idiot me orderd all the wrong junk from ballistic so im sending that back today.
next week im relly goign to concentrate on finishing the other head. and get it ready to install. I still neet to shim the springs and lap the valves, clean the surface and repaint.
Next weekend going to JY for Radiator, Auto Column, oil lines, and motor mounts. I have found ones on ebay but I need the Block Plates too! sucks. Gotta wait a little bit for the rear brakes and ECM tune.. Need to get some money set aside first.. Then im done!! Sorta
Tre, any word on shipping that pedal assembly?
#269
I usually get my OE Ford replacement parts at the dealer but the same Motorcraft plugs are available at the chain parts stores for way less - probably about half as much.
#273
Join Date: Aug 2008
Location: Loxahatchee, FL
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
like i mentioned before im gonna hit up the JY today for an Auto Column. As the time nears no harm in Swapping columns pre swap. i know Ill have the cable to tuck away and the shifter just chillen but if its one less thing to do come "Swap Weekend" then i can like for a week or 2...or 3 lol
#274